Comforter Sizes Chart: Twin, Full, Queen, King and California King - WhisperLinens

Comforter Sizes Chart: Twin, Full, Queen, King and California King

Comforter sizes vary by brand, but most fall into predictable ranges. A twin comforter is usually about 64–68 inches wide, a full or queen about 76–92 inches, and a king or California king about 102–110 inches. Lengths mostly run from 86 to 96 inches. Because there is no single US standard, the only numbers that matter for your purchase are the ones on the listing you’re looking at.

Below is a size chart, the simple math for working out how far a comforter will hang over your bed, and the cases where sizing up makes sense.

Comforter Size Chart

Size Typical comforter (inches) Mattress (inches) Approx. extra width per side
Twin 64–68 × 86–92 38 × 75 13–15 in
Twin XL 64–68 × 88–92 38 × 80 13–15 in
Full 76–90 × 86–96 54 × 75 11–18 in
Queen 88–92 × 88–96 60 × 80 14–16 in
King 102–110 × 86–96 76 × 80 13–17 in
California King 104–110 × 90–96 72 × 84 16–19 in

The comforter ranges are compiled from published size charts, including Pure Down’s and Purple’s, and the mattress sizes are standard US dimensions. “Extra width per side” is half the difference between comforter and mattress width, the fabric available to cover the side of the mattress.

Many brands also sell combined sizes. A Full/Queen comforter is one size meant for both beds, usually around 86–90 inches wide. A King/Cal King works the same way at the top end. These are practical, but they fit the smaller bed more generously than the larger one.

How to Work Out the Drop for Your Bed

  1. Measure the mattress width, length and depth, with any topper in place.
  2. Subtract the mattress width from the comforter width, then divide by two. That’s the extra fabric on each side.
  3. Compare it with the mattress depth. If the extra fabric is less than the depth, the comforter won’t reach the bottom edge of the mattress.
  4. Check the length. Subtract the mattress length from the comforter length to see what’s left for the foot of the bed and for tucking under pillows.

Example: a 90-inch-wide comforter on a 60-inch queen leaves 15 inches per side. On a 12-inch-deep mattress, that covers the side and drops about 3 inches below it. The same comforter on a 54-inch full leaves 18 inches per side, a noticeably longer drape. Our queen comforter size guide works through two real queen examples in more detail.

Should You Size Up?

Sizing up is common and often works well. A king comforter on a queen bed, for example, gives a fuller look and more coverage for two people who share. It makes sense if:

  • your mattress is deep or has a thick topper, so a standard size stops short of the edge;
  • two sleepers keep pulling the comforter to one side;
  • you like a long, generous drape rather than a tailored look.

It makes less sense if the bed sits close to a wall, if you use a bed skirt you want to show, or if the comforter is going inside a duvet cover. In that last case, the insert has to match the cover, not the bed.

Comforter Inside a Duvet Cover? Match the Cover

If you plan to put a comforter inside a cover, the bed size stops being the main measurement. Compare the comforter’s width and length with the cover’s. A comforter that’s much larger will bunch; one that’s much smaller will leave empty corners. Our guide to using a comforter as a duvet insert shows how to check the fit.

Duvet inserts are often cut closer to their covers than comforters are to beds. Our Cotton Comfort Duvet Insert, for example, comes in 150 × 200, 200 × 230 and 220 × 240 cm, with approximate inch sizes of 60 × 80, 80 × 90 and 86 × 94 on the listing. Compare the insert with the exact cover you plan to use. For the difference between the two layers, see duvet insert vs. comforter.

Comforter Sizes for Each Bed, in Brief

Twin and twin XL comforter size

Usually 64–68 inches wide. Twin XL comforters are often a few inches longer to match the 80-inch mattress, and many are sold as “Twin/Twin XL.” On a 38-inch mattress, that leaves about 13–15 inches per side.

Full comforter size

The widest range of any size, roughly 76–90 inches wide, because many “full” comforters are really Full/Queen. Check the width if you want a specific drape on a 54-inch full.

Queen comforter size

Usually about 88–92 inches wide and 88–96 inches long. On a 60-inch queen that gives 14–16 inches per side.

King and California king comforter size

Usually 102–110 inches wide. Because a California king is 4 inches narrower than a king, the same comforter hangs about 2 inches lower on each side of a Cal King. Look for at least 90 inches of length on a California king, which is 84 inches long.

Common Questions

What size comforter do I need for a queen bed?

A queen comforter of about 88–92 inches wide suits most queen beds. For a deep mattress or a longer drape, a king comforter is a common choice.

Can I use a queen comforter on a king bed?

It will cover the top, but with roughly 6–8 inches per side on a 76-inch king, it won’t hang far over the edges. Most people find it too small for two sleepers.

Is a full and queen comforter the same?

Often, yes: many are sold as one Full/Queen size. Some brands make separate sizes, so compare the listed width.

Are comforter sizes the same as duvet sizes?

Not necessarily. Comforters are sized for beds; duvet inserts are sized for their covers. Always compare the actual measurements. Our bed sheet size chart covers the sheets that go underneath.

Back to blog